Mar 16, 2022 Leave a message

How cement tiles are made

How cement tiles are made


These rock-solid, durable tiles are made with century-old craftsmanship. The tiles are made of marble, portland cement and natural mineral pigments. The tiles are made of three layers, and they are subjected to enormous pressure from a mechanical hydraulic press. Our tiles didn't get burned. Pressed tiles are soaked and cured naturally like structural concrete. Each tile is individually handcrafted and is a work of art. There will always be subtle changes to each tile, that's part of the charm


Cement tile mould

Before making any cement bricks, you need molds. Shape molds, sometimes called "frames," are needed to hold the shape of the tile. These are usually divided into three to four pieces. The cement brick is upside-down, so the bottom plate of the mould will touch the surface of the new brick. These are usually polished flat, but some are given an embossed pattern to create textured tiles for better slip resistance on sidewalks, and other uses as outdoor pavers. The frame is attached to the base to shape the sides. These are usually made in two parts that clip onto the base. The top piece, sometimes called a "cork," acts as a cover after the tiles are assembled to evenly distribute the pressure of the hydraulic press.


The magic of making painted cement tiles comes from the handcrafted pattern molds used to create colorful patterns in the tiles. Similar to a delicate cookie-cutter, the patterned grid has different sections into which the coloured mixture is poured. This pattern grid is securely set in a mold frame that defines the tile boundaries. While a tile maker may have very few shape molds...per workstation, maybe only one 8"x8" frame, and even fewer other shapes, there will be hundreds or even a thousand or more pattern molds per store. Most stores will have at least one full-time artisan dedicated to making pattern molds.



mix colors

The skill and artistry required to make color pastes is probably more than anyone else in the shop, rivaled only by mold makers. The pigmented surface layer starts with a very wet concrete slurry. The exact formula is usually a family secret. White Portland cement is used for this layer instead of the standard grey cement used in the tile body. Sand used as an aggregate is also the best among tiles. Coarser aggregates are used for deeper layers. The slurries are colored with natural mineral pigments such as iron, cobalt and chromium oxides. To add a little more difficulty, the color changes slightly as the cement cures, and again when it's sealed. That's why we always seal our sample tiles in order to provide our customers with the best representation of their finished installation.


Create a surface layer

Once the station has the required materials ready, tile production begins. Oil the mold base (for clean demolding and better surface texture), assemble the frame, and insert the pattern mold. Artisans carefully pour the appropriate colorant into each area.


At this stage, I saw three different styles. The tool shown in the video can best be described as a plugged funnel. Hold the colorant in the funnel with a stopper on the stem. When the craftsman positions the funnel over an area of color, he lifts the stopper long enough to release the correct amount of colored cement. Another very common tool resembles a cross between a garden trowel and a gravy boat, with deep grooves and a very narrow pour spout. Finally, I've also seen utensils that resemble cooking spoons with handles sticking straight out of the cup end.


When all areas are poured, the mold is shaken, twisted, vibrated or tapped to help disperse the color and allow potential air bubbles to dissipate on their own. The pattern mold is then removed from the frame for the next step.


Create the cement brick body

According to your requirements, cement bricks can have two or three layers. We tend to mention just two: the color layer and the tile body, but production does require three different formulas.


After removing the model mold, use a sieve to add a very fine sand and cement mixture to the mold. When pressed, most of the moisture in the color layer will be pushed into the layer, allowing the color layer to dry enough to hold its solid shape. This layer is applied very carefully so that the color layer is not disturbed.


Next, the remaining host material is usually added by hand. This would include the same basic components as concrete, with much coarser aggregates than surface and intermediate aggregates. This layer provides strength and should have a rough texture to help the thin mortar adhere to the tile during installation.


At every step of the process, tile manufacturers can be seen cleaning up excess and working to achieve consistent density and levels. You may notice some slight packing around the edges and corners. This helps produce sharper, more resilient edges in the finished tile.



Press and Finish

After the tiles are built, the frame is covered with cork and then compacted with a hydraulic press. The pressure pushes the air out and balances the moisture in the color layer. Compacted tiles are strong enough to handle gently.


Remove the tile from the mold. First, release the pressure on the frame clips and allow the tile maker to lift the frame from the sandwich of tile and steel. The pressure of the cork helps prevent any material on the edge from lifting off the tile. Remove the cork, then carefully separate the tile from the base and place on a shelf.


Good tile makers are very picky and reminds me of good interior painters. At the end of the day, tile makers often get cement and marble dust on their shirts and aprons, but they constantly brush and clean molds and worktops. At each stage, they collect excess to move on to the next tile with as little waste as possible.


The finished tile is now only missing moisture and time. Concrete is a mixture of cement, aggregate (sand, gravel, etc.) and water. Cement bricks may use more precisely controlled compositions than structural concrete, but the basic process is the same. Over time, cement will chemically set and harden. Instead of cement drying, it undergoes hydration and carbonation, a chemical reaction that converts calcium oxide in Portland cement into calcium hydroxide, and ultimately into calcium carbonate.


After pressing, the cement bricks are soaked in water to ensure proper hydration and curing. It takes about 4 weeks for cement to reach 90% of its potential strength and will continue to gain strength for decades.


Send Inquiry

whatsapp

Phone

E-mail

Inquiry